Materials Engineering and Processing
Apply to PD 13-8092 as follows:
For full proposals submitted via FastLane:
standard Grant Proposal Guide proposal preparation guidelines apply.
For full proposals submitted via Grants.gov:
the NSF Grants.gov Application Guide; A Guide for the Preparation and Submission of NSF Applications
via Grants.gov Guidelines applies.
(Note: The NSF Grants.gov Application Guide is available on the Grants.gov website and on the
NSF website at: http://www.nsf.gov/publications/pub_summ.jsp?ods_key=grantsgovguide)
Important Information for Proposers
A revised version of the NSF Proposal & Award Policies & Procedures Guide (PAPPG) (NSF 15-1), is
effective for proposals submitted, or due, on or after December 26, 2014. The PAPPG is consistent
with, and, implements the new Uniform Administrative Requirements, Cost Principles, and Audit
Requirements for Federal Awards (Uniform Guidance) (2 CFR § 200). Please be advised that
the guidelines contained in NSF 15-1 apply to proposals submitted in response to this
Full Proposal Window: September 1, 2015
September 15, 2015
September 1 - September 15, Annually Thereafter
Full Proposal Window: February 1, 2016
February 16, 2016
February 1 - February 15, Annually Thereafter
Full Proposal Window: September 1, 2016
September 15, 2016
September 1 - September 15, Annually Thereafter
Due dates repeat annually. Please reference the CMMI main page for further specifics concerning unsolicited proposal submission windows.
The Materials Engineering and Processing (MEP) program supports fundamental research addressing the processing and mechanical performance of engineering materials by investigating the interrelationship of materials processing, structure, properties and/or life-cycle performance for targeted applications.
Materials processing proposals should focus on manufacturing processes that convert material into useful form as either intermediate or final composition. These include processes such as extrusion, molding, casting, deposition, sintering and printing. Proposed research should include the consideration of cost, performance, and feasibility of scale-up, as appropriate. Novel processes for the production of nanoscale materials (nanotubes, nanocrystals, etc.) are of interest. Process optimization studies without a fundamental scientific contribution are not supported.
Research proposals related to mechanical performance should be driven by a targeted application(s). Structural materials that, in service, bear mechanical load are of interest. These include materials such as metals, polymers, composites, biomaterials, ceramics, hybrids and cement, intended for applications ranging from the microscale (e.g., MEMS) to the macroscale (e.g., civil infrastructures). Research related to the deterioration of performance during service (e.g., corrosion and degradation) is also of interest.
In some cases, the performance of functional materials is also of interest. This includes materials that possess native properties and functions that can be controlled by external influences (e.g., temperature, light and pH) as well as responsive materials (e.g., piezoelectric, chromogenic, shape memory and self-healing). Research proposals on performance of electronic materials to be used for energy storage or conversion (e.g., fuel cells, batteries and PVs) are not appropriate for the MEP program. One exception to this would be for proposals related to multifunctional (versus a single function) material performance that include a consideration of mechanical performance. Proposals on this topic are encouraged.
Research plans driven by scientific hypotheses are encouraged. Material structures across length scales ranging from nano to meso to macro are of interest. Research on materials in the bulk or in special configurations such as surfaces or interfaces is appropriate as are research proposals related to surface engineering or tribology. Analytical, experimental, and/or numerical studies are supported. Collaborative proposals with industry (GOALI) are encouraged.
Proposals related to additive manufacturing, laser processing or bonding/joining processes are welcome in CMMI and should be submitted to the Manufacturing Machines and Equipment (MME) program, even if the focus of such proposals is on the materials for those processes. Proposals addressing the manufacture (scale up, quality, reliability, etc.) of nanoscale materials, structures, devices and systems should be submitted to the Nanomanufacturing (NM) program. Proposals addressing atomic/molecular scale synthesis or thin film synthesis (as opposed to manufacturing) are not appropriate for the MEP program. Research proposals on electronic materials to be used for energy storage or conversion (e.g., fuel cells, batteries, PVs) are not appropriate for the MEP program unless there is new science being proposed about manufacturing processes for these materials. Research on the mechanics of solid materials should be directed to the Mechanics of Materials (MoM) program. Investigators with proposals focused on design methodological approaches and theory enabling the accelerated development and insertion of materials should consider the Design of Engineering Material Systems (DEMS) program. In response to the Materials Genome Initiative, there is a special initiative for research on a combined theoretical and experimental approach to accelerate materials discovery and development; such proposals should be directed to the Designing Materials to Revolutionize and Engineer Our Future (DMREF) opportunity.
PIs are encouraged to email a project summary to email@example.com at least a few weeks before the proposal submission deadline to determine if the research topic aligns with the MEP program.
Investigators wishing to serve on a proposal review panel should send an email to firstname.lastname@example.org with a short biographical sketch, a list of areas of expertise and a link to their home page.
REU/RET supplement requests should be submitted by March 31 each year.
Mechanics of Materials and Structures
Design of Engineering Material Systems
Manufacturing Machines and Equipment
Slides from the NSF Webinar on the Materials Engineering and Processing (MEP), August 21, 2013
Dear Colleague Letter - Designing Materials to Revolutionize and Engineer our Future (DMREF)
THIS PROGRAM IS PART OF
What Has Been Funded (Recent Awards Made Through This Program, with Abstracts)
Map of Recent Awards Made Through This Program